The ice manufacturer line to my fridge presently doesn’t have shutoff valve and I also’d love to include one but i can not find out exactly what size the connector is

The ice manufacturer line to my fridge presently doesn’t have shutoff valve and I also’d love to include one but i can not find out exactly what size the connector is

we bought a 1/4 inch valve considering that the ice manufacturer connector we have actually says 1/4 FCM it did not fit on it but. It appears similar to 1/8 inches, but a 1/8 inches valve does not fit either, though it is quite near. Where could I find information on water pipeline sizes, there needs to be some standard?

The copper water line i will be linking it to has got the precise measurement that is same the refrigerator.


Okay I was thinking that looking the web for 1/4″ OD Valve Male Female would get me personally the thing I require but i will be getting no outcomes and so I’ve reopened issue! Can anybody offer me personally an internet connect to an item which will fit? I have added an image for the present connection where let me include the valve. Many Thanks!

3 Answers 3

You will find various requirements to pipelines and threads. Your problem is you are making an effort to mix two various standards that are threaded.

The ball valve which you connected to has nationwide pipeline threads (NPT). NPT are tapered plus it is taper that produces the seal from a female and male joint. No washers are expected.

What exactly is shown in your picture is compression fixtures that have a right or thread that is running. The seal is created by either a ferrule or a plastic washer.

The connection between the copper tube and the supply hose has been made as follows in your case

1/4″ Copper Tube > 1/4″ Compression by 1/4″ Compression Coupling > 1/4″ Supply Hose

The seal on a ferrule makes the copper tube this is certainly positioned underneath the nut. While the nut is tightened, the ferrule is compressed involving the coupling in addition to pipeline.

The seal on the supply hose part is manufactured with a plastic washer which can be frequently integral the the nut of this supply hose. (The compression coupling might have include two pea pea pea nuts, certainly one of that has been discarded because the supply hose has one integral.)

Therefore, to respond to your concern, you simply require a 1/4″ compression x 1/4″ compression valve that may change the present coupling. Let me reveal a web link to this type of valve.

Do the paperwork is had by you that was included with the refrigerator? It will show the ice maker install and maybe state the dimensions of this valve. I’ve constantly seen that it is 1/4″.

Where may be the water line tapped from? Frequently it comes down a 1/2″ copper pipeline. You can place your valve regarding the copper pipeline part.

EDIT: web web web Page 33 associated with installation manual states that the water supply pipe is 1/4″ OD. You’ll need a 1/4″ valve. Be certain there are not any burrs from the copper tubing after it is cut by you. Often you’ll want to register the sides. In the event that pipeline cutter is certainly not razor- sharp it could mushroom the ends and which will ensure it is appear it is perhaps maybe maybe not the right diameter.

When you have more hours and cash, the advisable thing is to run either a 1/2 inches copper line or even a 1/2 galvanized line towards the straight back of one’s fridge having a 1/4 inches connection about it, ideally set within the wall surface in synthetic field. An alternative cheaper means is always to run a 1/4 inches line through the 1/4 inches connection at your twin shut off valve using your destroy. Nonetheless, the copper line is a line that is hard it gets crimped specially when you or somebody else is careless in going the refrigerator around to completely clean or any.

Utilizing two crescent wrenches, this is what to complete in the event that you curently have a hard copper line towards the straight back without a shut down valve anywhere in site. You can aquire a kit who has the components you will need, 1/4 inches connectors having a 6 base, 1/4 inch supply hose, which has the 1/4 pea nuts on both ends. Carefully take action your self or get yourself a plumber to slice the copper line with a copper pipe cutter, an excellent cut that is clean a number of ins this part of where in actuality the line happens of wall surface or case (provided that it isn’t crimped, you are ok to cut it).

Place the free 1/4 inches nut on backwards in the pipeline, so that the nut covers the ferrel tucked in during the side of the final end for the pipeline, then, screw regarding the 1/4 inches connector/adjuster about it, utilizing the 1/4 inches threads towards the 1/4 inches nut regarding the hose, and tighten up, snug, never ever overbearing, ever with any plumbing system. Then link one other end of hose/nut into the end that is threaded the fridge at the end, snug! Keep In Mind! But, a very important thing to complete whenever you are linking a line to either a tap or ice box or in any case can be, just before put that final connection in the fridge, put that result in a huge bucket and turn it in to clear the type of atmosphere and grub, because that knows just how long it has been sitting. Plus, if you air within the lines, that is a entire nother frustration, believe me you don’t wish! Obtain the fresh air down! You are able to do all this yourself too! Do not forget to always check every thing for leakages! Best of luck! Now get commemorate you merely conserved your self $150.

Deixe uma resposta

O seu endereço de email não será publicado. Campos obrigatórios marcados com *